Car, CHEVROLET, Orlando, 2011, 2.0L (LBN) - 2.0L (LBN)

Mobile equipment identifier: --

CD changer - hardware version: --

VIN no: W0LGT8EBXA1007787

Body type: Station wagon

Engine name: 66

Engine type: 66

System identification: BOSCH0100

Hardware version: --

Software version: --

System name: --

Subscriber ID: O100057235

Programming date: 8209

Identifier: 00 00

System code: 00

XML configuration compatibility identifier: 1

XML data file part number: 0

XML data file alpha code:

Previous subscriber ID: *10MDZ7

2nd previous subscriber ID: *10MDZ7

Manufacturer enable counter (MEC): 0

Trailer hitch: --

ECU - diagnostic address: --

Manufacturer's traceability number: --

Broadcast code: --

ROM ID: --

Boot software part number: 12639237

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 - identifier: 55577209

Software module 4 - identifier: 55577673

Software module 5 - identifier: 55573530

Software module 6 - identifier: 55573530

Software module 7 - identifier: 55573530

Software module 8 - identifier: 55573530

Software module 9 - identifier: --

Software module 10 - identifier: --

End model part number: 55577619

Base model part number: 55574337

Software part number alpha code: --

Software module 1 identifier alpha code: AA

Software module 2 identifier alpha code: AA

Software module 3 identifier alpha code: AA

Software module 4 identifier alpha code: AA

Software module 5 identifier alpha code: --

Software module 6 identifier alpha code: --

Software module 7 identifier alpha code: --

Software module 8 identifier alpha code: --

Software module 9 identifier alpha code: --

Software module 10 identifier alpha code: --

End model part number alpha code: 00

Base model part number - alpha code: 00

GMLAN identification data - bus 1 type: High speed CAN-bus

GMLAN identification data - GMLAN kernel 1 version: 00 00

GMLAN identification data - data dictionary 1 version: --

GMLAN identification data - bus 2 type: --

GMLAN identification data - GMLAN kernel 2 version: --

GMLAN identification data - data dictionary 2 version: --

Clear DTC

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0.0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

EVAP purge solenoid valve - command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Barometric pressure sensor: 0.0 kPa

Calculated catalyst temperature: -40 °C

Control module voltage: 0.00 V

Ignition 1 signal: 0.0 V

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Throttle position - target: 0 %

Electronic throttle control (ETC) system - forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) - motor: Enabled

Throttle position sensors 1 and 2: Agree

Cooling fan relays 2 and 3 - command: Off

Cooling fan relay 1 - command: Off

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C off for WOT: No

A/C compressor clutch relay - command: Off

Extended travel brake pedal position signal: Inactive

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal starter inhibit switch: On

Clutch pedal switch: Released

O2 sensor 2, bank 1 - heater: Off

O2 sensor 1, bank 1 - heater: Off

Engine oil pressure switch: Ok

Engine oil indicator - change command: Off

Low engine oil pressure indicator - command: Off

Cold start: No

P/N switch: Inactive

Engine controls ignition relay - command: Off

Ignition accessory signal: Off

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position - performance test: Ok

MAP - performance test 2: Ok

MAP - performance test 1: Ok

MAF performance test: Ok

A/C high side pressure sensor: 0.00 V

Engine oil - temperature calculated: -40 °C

Crankshaft position - active counter: 0 Counts

Crankshaft position - resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire, cylinder 3 - historic: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Warm-ups without emission malfunctions: 0 Counts

Warm-ups without non-emission malfunctions: 0 Counts

Accelerator pedal - position sensors: 0 %

Throttle - position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time, bank 1: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Fuel tank - rated capacity: 0 L

Accelerator pedal - position: 0 %

Catalyst monitor - test counter: 0 Counts

MIL - control circuit high voltage test status: Malfunction

MIL - control circuit low voltage test status: Malfunction

MIL - control circuit open test status: Malfunction

A/C compressor clutch relay - control circuit high voltage test status: Malfunction

A/C compressor clutch relay - control circuit low voltage test status: Malfunction

A/C compressor clutch relay - control circuit open test status: Malfunction

Throttle position sensor 1 - fully close learn: 0.00 V

Throttle position sensor 2 - fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor - PWM control signal: 0 %

Intake camshaft position actuator solenoid valve - control circuit high voltage test status: Malfunction

Intake camshaft position actuator solenoid valve - control circuit low voltage test status: Malfunction

Intake camshaft position actuator solenoid valve - control circuit open test status: Malfunction

Exhaust camshaft position actuator solenoid valve - control circuit high voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve - control circuit low voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve - control circuit open test status: Malfunction

Ignition coil 1 - control circuit high voltage test status: Malfunction

Ignition coil 1 - control circuit low voltage test status: Malfunction

Ignition coil 1 - control circuit open test status: Malfunction

Ignition coil 2 - control circuit high voltage test status: Malfunction

Ignition coil 2 - control circuit low voltage test status: Malfunction

Ignition coil 2 - control circuit open test status: Malfunction

Ignition coil 3 - control circuit high voltage test status: Malfunction

Ignition coil 3 - control circuit low voltage test status: Malfunction

Ignition coil 3 - control circuit open test status: Malfunction

Ignition coil 4 - control circuit high voltage test status: Malfunction

Ignition coil 4 - control circuit low voltage test status: Malfunction

Ignition coil 4 - control circuit open test status: Malfunction

Cylinder 1 injector - control circuit high voltage test status: Malfunction

Cylinder 1 injector - control circuit low voltage test status: Malfunction

Cylinder 1 injector - control circuit open test status: Malfunction

Cylinder 2 injector - control circuit high voltage test status: Malfunction

Cylinder 2 injector - control circuit low voltage test status: Malfunction

Cylinder 2 injector - control circuit open test status: Malfunction

Cylinder 3 injector - control circuit high voltage test status: Malfunction

Cylinder 3 injector - control circuit low voltage test status: Malfunction

Cylinder 3 injector - control circuit open test status: Malfunction

Cylinder 4 injector - control circuit high voltage test status: Malfunction

Cylinder 4 injector - control circuit low voltage test status: Malfunction

Cylinder 4 injector - control circuit open test status: Malfunction

Cooling fan relay 1 - control circuit high voltage test status: Malfunction

Cooling fan relay 1 - control circuit low voltage test status: Malfunction

Cooling fan relay 1 - control circuit open test status: Malfunction

Cooling fan relays 2 and 3 - control circuit high voltage test status: Malfunction

Cooling fan relays 2 and 3 - control circuit low voltage test status: Malfunction

Cooling fan relays 2 and 3 - control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 - heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 - heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 - heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

O2 sensor 1, bank 1 - heater: 0 %

O2 sensor 1, bank 1 - heater: 0.0 A

O2 sensor 2, bank 1 - heater: 0.0 A

Engine controls ignition relay - control circuit high voltage test status: Malfunction

Engine controls ignition relay - control circuit low voltage test status: Malfunction

Engine controls ignition relay - control circuit open test status: Malfunction

Engine controls ignition relay - feedback signal: 0.0 V

Cruise control: Inactive

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

A/C high side pressure sensor: 0 kPa

Fuel trim system test state: Disabled

Short term fuel trim test average: -100 %

Long term fuel trim test average: -100 %

Long term fuel trim test average without purge: -100 %

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 1: No

Injector, cylinder 4 - disabled, misfire detected: No

Injector, cylinder 3 - disabled, misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Exhaust camshaft position - command: 0 %

Intake camshaft position - command: 0 %

O2 sensor 2, bank 1 - heater: 0 %

Exhaust camshaft - position: 0 °

Intake camshaft - position: 0 °

Exhaust camshaft - target position: 0.0 °

Intake camshaft position - target: 0.0 °

Exhaust camshaft - position variance: 0.0 °

Intake camshaft position - variance: 0 °

Exhaust camshaft position active counter: 0 Counts

Intake camshaft position - active counter: 0 Counts

Transmission oil temperature: -40 °C

A/T output speed: 0 rpm

Torque delivered signal: 0.00 N·m

Intake manifold pressure: 0 kPa

Start-up IAT sensor: -40 °C

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor - learned apply position: 0.00 V

Clutch pedal - position learn status: Performed successfully

Clutch pedal position sensor - learned release position: 0.00 V

Clutch pedal position sensor: 0 %

Service vehicle soon (SVS) indicator - command: Off

MIL - requested by DTC: No

Check engine telltale: Off

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Redundant odometer memory: Not present

Transmission OSS signal - replicated: 0 rpm

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing: No

Torque request inhibit - ignition timing advance: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

Throttle body - idle air flow compensation: 0.0 %

Catalyst monitor - test result: No decision

Catalyst monitor - not at idle test conditions met: No

Catalyst monitor - test state: Inactive

Reduced engine power history: Not supported

Accelerator pedal position sensor 1 - learned applied position: 0.0 %

Accelerator pedal position sensor 2 - learned applied position: 0.0 %

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Ignition 1 signal: 0.0 V

Throttle position - target: 0 %

Extended travel brake pedal position signal: Inactive

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal switch: Released

Starter relay - command: Off

Traction control torque request signal: 0.0 %

Traction control torque delivered signal: 0 %

Torque management ignition timing retard: 0.0 °

Target idle speed: 0 rpm

Throttle - position: 0 %

Cruise control - disengagement 1st history: Brake pedal applied

Cruise control - disengagement 2nd history: Brake pedal applied

Cruise control - disengagement 3rd history: Brake pedal applied

Cruise control - disengagement 4th history: Brake pedal applied

Cruise control - disengagement 5th history: Brake pedal applied

Cruise control - disengagement 6th history: Brake pedal applied

Cruise control - disengagement 7th history: Brake pedal applied

Cruise control - disengagement 8th history: Brake pedal applied

Accelerator pedal - position: 0 %

Cruise control 'On'/'Off' switch: Off

Cruise control 'Set/Coast' switch: Off

Cruise control 'Resume/Accelerate' switch: Off

Cruise control: Inactive

Cruise control switch: Active

Transmission OSS signal - replicated: 0 rpm

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition 1 signal: 0.0 V

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal starter inhibit switch: On

Engine oil pressure switch: Ok

Starter relay - command: Off

P/N switch: Inactive

Engine controls ignition relay - command: Off

Ignition accessory signal: Off

Remote vehicle start request signal: Off

Crank request signal: No

Generator F terminal signal: 0.0 %

Immobilizer - fuel enable: No

ECM in immobilizer fail enable mode: No

Immobilizer password learned: No

Immobilizer - fuel disable until ignition off: No

Immobilizer automatic learn timer: Inactive

Accelerator pedal - position: 0 %

Starter relay - control circuit high voltage test status: Malfunction

Starter relay - control circuit low voltage test status: Malfunction

Starter relay - control circuit open test status: Malfunction

Generator L-terminal - command: 0.0 %

Engine controls ignition relay - control circuit high voltage test status: Malfunction

Engine controls ignition relay - control circuit low voltage test status: Malfunction

Engine controls ignition relay - control circuit open test status: Malfunction

Engine controls ignition relay - feedback signal: 0.0 V

Generator L-terminal circuit - high voltage test status: Malfunction

Generator L-terminal circuit - low voltage test status: Malfunction

Generator L-terminal circuit - open test status: Malfunction

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer - security information programmed: No

Immobilizer system - status: Standby

Immobilizer - password learn: Inactive

Immobilizer - security code accepted: No

Immobilizer - security code function: Not present

Immobilizer - security code programmed: No

Immobilizer - security code lockout: No

Immobilizer - password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

MIL - requested by DTC: No

Electric power management - inhibit reason: None

Engine coolant temperature sensor: -40 °C

Vehicle speed sensor: 0 km/h

Intake air temperature sensor: -40 °C

Barometric pressure sensor: 0.0 kPa

Catalyst monitor - enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

HO2S heater monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor - complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Ignition 1 signal: 0.0 V

Ambient air temperature: -40 °C

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal switch: Released

Cold start: No

Coolant temperature at engine start: -40 °C

Engine off time: 00:00:00

Start-up IAT sensor: -40 °C

MIL - requested by DTC: No

Check engine telltale: Off

Check engine telltale - request: No

Misfire monitor enabled: No

Misfire monitor complete: No

Fuel system monitor - enabled: No

Fuel system monitor - complete: No

Component monitor - enabled: No

Component monitor - complete: No

Catalyst monitor - enabled: --

A/C system refrigerant monitor - enabled: --

Catalyst monitor - enabled: --

O2S/HO2S monitor enabled: --

HO2S heater monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor - complete: --

Catalyst monitor - complete: --

A/C system refrigerant monitor - complete: --

O2S/HO2S monitor complete: --

HO2S heater monitor complete: --

EGR/Camshaft position monitor - complete: --

Number of DTC: 0 Counts

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0.0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

EVAP purge solenoid valve - command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Barometric pressure sensor: 0.0 kPa

Calculated catalyst temperature: -40 °C

Control module voltage: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Throttle position - target: 0 %

Throttle - position: 0 %

A/C compressor clutch relay

Cooling fan relay 1

Cooling fan relays 2 and 3

Cooling fan relays 1, 2 and 3

Fuel trim enable

Evaporative emission (EVAP) system, canister purge valve

Engine controls ignition relay

Engine speed

Throttle position

Exhaust camshaft position actuator

Exhaust camshaft position actuator solenoid valve

Intake camshaft position actuator

Intake camshaft position actuator solenoid valve

Fuel control loop status

Generator L terminal

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

Check engine telltale

Starter relay

Clutch pedal position learning

Crankshaft position variation learn

O2 sensor learning

Idle learn

Reset oil life

Fuel trim reset